免费会员 经销商
参考价：
-
- 面议
FPQLI-Q1 二极管泵浦调Q激光器-8ns
具体成交价以合同协议为准
2021-08-17
- 型号
- FPQLI-Q1
该企业相似产品
产品简介
这款二极激光器技术,可输出1064nm,532nm,355nm,266nm,213nm,1053nm,526.5nm,351nm,263nm,211nm激光波长,采用Nd:YAG半导体泵浦固体激光DPSS技术制造,结构紧凑而能量稳定,非常适合激光诱导击穿光谱LIBS,光致荧光光谱LIF,激光烧蚀和激光遥感等应用
详细信息
激光器技术,可输出1064nm,532nm,355nm,266nm,213nm,1053nm,526.5nm,351nm,263nm,211nm激光波长,采用Nd:YAG半导体泵浦固体激光DPSS技术制造,结构紧凑而能量稳定,非常适合激光诱导击穿光谱LIBS,光致荧光光谱LIF,激光烧蚀和激光遥感等应用。
二极管泵浦调Q激光器特点
输出高达45mJ脉冲能量，平均功率可达0.5W
二极管泵浦调Q激光器特点
输出高达45mJ脉冲能量，平均功率可达0.5W
空气冷却制冷,不需要水冷
短脉冲脉宽＜8ns
重复频率可调
内置同步脉冲发生器，用于触发用户其它设备，方便使用。
通过内置的以太网或WiFi接口进行远程控制
可选二倍频,三倍频,四倍频或五倍频等谐波发生器。
可选基频光衰减器
可选的光纤耦合输出
寿命高达2G个激光脉冲
二极管泵浦调Q激光器简述
二极管泵浦调Q激光器简述
二极管泵浦调Q激光器是一款紧凑高效的空气制冷Q开关激光器,具较高的脉冲峰值功率，非常适合激光诱导击穿光谱LIBS,光致荧光光谱LIF,激光烧蚀和激光遥感等应用。
二极管泵浦调Q激光器可产生45mJ@10Hz或10mJ@50Hz的激光脉冲,具有超低发散角和较高的倍频高可到倍频波长211nm,使用OPO后波长可扩展到红外范围。
采用全空气冷却模式得益于它优越的wall-plug效率，液体不用于传热，因此不需要经常更换冷却液或清洗冷却系统。在内部触发模式下具有较低抖动,可采用脉冲触发用户设备,如果需要，激光脉冲可以从延时发生器外部触发,允许在单次发射（single-shot）或可变脉冲重复模式下操作。
具有以太网接口,方便从电脑上控制和监测激光器,WiFi可选。
这款二极管泵浦调Q激光器可配置1053nm和1064nm基频波长，其中1053nm激光器采用Nd:YLF晶体，可以在单脉冲到重复频率范围内工作，而不改变发散角和光束质量。
二极管泵浦调Q激光器应用
这款二极管泵浦调Q激光器可配置1053nm和1064nm基频波长，其中1053nm激光器采用Nd:YLF晶体，可以在单脉冲到重复频率范围内工作，而不改变发散角和光束质量。
二极管泵浦调Q激光器应用
激光诱导击穿光谱LIBS
时间飞行光谱TOFS
激光诱导荧光光谱LIF
激光闪光光解
基质辅助激光解析电离MALDI
脉冲光沉积PLD
遥感
激光烧蚀
TFT-LCD激光修复
PIV激光粒子图形测速
二极管泵浦调Q激光器技术参数
时间飞行光谱TOFS
激光诱导荧光光谱LIF
激光闪光光解
基质辅助激光解析电离MALDI
脉冲光沉积PLD
遥感
激光烧蚀
TFT-LCD激光修复
PIV激光粒子图形测速
二极管泵浦调Q激光器技术参数
重复频率为 10 Hz 配置的参数1)
| 型号 | Q1 | |||
-B10 | -C10 | -D10 | -E10 | |
| 波长 | 1053 or 1064 nm | 1064 nm | 1053 nm | |
| 脉冲频率2) | Single-shot to 10 Hz | |||
| 脉宽 3) | < 8 ns | < 7 ns | ||
| 单脉冲能量@ 4) | ||||
| 1053/1064 nm | 10 mJ | 20 mJ | 35 mJ | 45 mJ |
| 526.5/532 nm | 5 mJ | 10 mJ | 17 mJ | 22 mJ |
| 351/355 nm | 3 mJ | 6 mJ | 10 mJ | 13 mJ |
| 263/266 nm | 1.5 mJ | 3 mJ | 5 mJ | 7 mJ |
| 211/213 nm | 0.5 mJ | 1 mJ | 2 mJ | 2.5 mJ |
| 脉冲-脉冲能量稳定性 @ 5) | ||||
| 1053/1064 nm | <0.5 % RMS | |||
| 526.5/532 nm | <2.5 % RMS | |||
| 351/355 nm | <3.5 % RMS | |||
| 263/266 nm | <4 % RMS | |||
| 211/213 nm | <5 % RMS | |||
| 功率漂移 6) | ± 3.0 % | |||
光束质量 | Bell-shaped, >75 % fit to Gaussian | |||
| 光束发散角 7) | <1 mrad | |||
| 光束定位稳定性8) | < 10 µrad | |||
| 偏振 | Linear, horizontal | |||
| 光束直径 9) | 1.7 mm | 2.5 mm | 3.5 mm | |
| 抖动 10) | < 0.5 ns RMS | |||
| 可选电控激光能量衰减器 10) | ||||
透过率范围 | 0.5 – 95 % | |||
| 尺寸 | ||||
| 激光头 ( W×L×H) | 110 × 231× 112 mm3 | |||
| 控制器 (W×L×H) | 108× 191 × 59 mm3 | |||
| 功率适配器 (W×L×H)12) | 50 × 125 × 31 mm3 | |||
| 谐波发生器 (W×L×H)13) | 110 × 242× 112 mm3 | |||
| 工作条件 | ||||
制冷方式 | Air cooled | |||
| 环境温度 | 15 – 30 ºC | |||
| 相对湿度 | 10 – 80 % (non-condensing) | |||
| 电压-供电要求 | 90-230 VAC, single phase, 47-63 Hz 14) | |||
| 功耗 | 15 W | 25 W | 30 W | |
重复频率20 Hz 版本参数规格1)
| Model | Q1 | ||
-B20 | -C20 | -D20 | |
| Wavelength | 1053 or 1064 nm | ||
| Pulse repetition rate2) | Single-shot to 20 Hz | ||
| Pulse duration 3) | <8 ns | ||
| Pulse energy @ 4) | |||
| 1053/1064 nm | 8 mJ | 15 mJ | 25 mJ |
| 526.5/532 nm | 4 mJ | 7.5 mJ | 12.5 mJ |
| 351/355 nm | 2.5 mJ | 5 mJ | 7.5 mJ |
| 263/266 nm | 1 mJ | 1.8 mJ | 3 mJ |
| 211/213 nm | 0.4 mJ | 0.7 mJ | 1.2 mJ |
| Pulse to pulse energy stability @ 5) | |||
| 1053/1064 nm | < 0.5 % RMS | ||
| 526.5/532 nm | <2.5 % RMS | ||
| 351/355 nm | <3.5 % RMS | ||
| 263/266 nm | <4 % RMS | ||
| 211/213 nm | <5 % RMS | ||
| Power drift 6) | ± 3.0 % | ||
Beam profile | Bell shaped, >75 % fit to Gaussian | ||
| Beam divergence 7) | <1.5 mrad | ||
| Beam pointing stability 8) | < 20 µrad | ||
| Polarization | Linear, horizontal | ||
| Typical beam diameter 9) | 1.7 mm | 2.0 mm | 2.5 mm |
| Jitter 10) | < 0.5 ns RMS | ||
| Optional motorized attenuator 11) | |||
Transmission range | 1 – 95 % | ||
| Dimensions | |||
| Laser head ( W×L×H) | 110 × 231× 112 mm3 | ||
| Controller unit (W×L×H) | 108× 191 × 59 mm3 | ||
| Power adapter (W×L×H)12) | 50 × 125 × 31 mm3 | ||
| Harmonic generator (W×L×H)13) | 110 × 242× 112 mm3 | ||
| Operating requirements | |||
Cooling requirements | Air cooled | ||
| Ambient temperature | 15 – 30 ºC | ||
| Relative humidity | 10 – 80 % (non-condensing) | ||
| Mains voltage | 90-230 VAC, single phase, 47-63 Hz 14) | ||
| Average power consumption | <30 W | ||
重复频率50 Hz 版本规格参数 1)
| Model | Q1 | ||
-50 | -A50 | -B50 | |
| Wavelength, nm | 1053 or 1064 nm | ||
| Pulse repetition rate2) | Single-shot to 50 Hz | ||
| Pulse duration 3) | < 10 ns | <9 ns | <8 ns |
| Pulse energy @ 4) | |||
| 1053/1064 nm | 2.5 mJ | 5 mJ | 10 mJ |
| 526.5/532 nm | 1.2 mJ | 2.5 mJ | 5 mJ |
| 351/355 nm | 0.6 mJ | 1.5 mJ | 3 mJ |
| 263/266 nm | 0.3 mJ | 0.7 mJ | 1.5 mJ |
| 211/213 nm | 0.1 mJ | 0.2 mJ | 0.5 mJ |
| Pulse to pulse energy stability @ 5) | |||
| 1053/1064 nm | < 0.5 % RMS | ||
| 526.5/532 nm | <2.5 % RMS | ||
| 351/355 nm | <3.5 % RMS | ||
| 263/266 nm | <4 % RMS | ||
| 211/213 nm | <5 % RMS | ||
| Power drift 6) | ± 3.0 % | ||
Beam profile | Nearly TEM00, >80 % fit to Gaussian | ||
| Beam divergence 7) | <1.5 mrad | ||
| Beam pointing stability 8) | < 20 µrad | ||
| Polarization | Linear, horizontal | ||
| Typical beam diameter 9) | 1.0 mm | 1.3 mm | 1.5 mm |
| Jitter 10) | < 0.5 ns RMS | ||
| Optional motorized attenuator 11) | |||
Transmission range | 1 – 95 % | ||
| Dimensions | |||
| Laser head ( W×L×H) | 110 × 231× 112 mm3 | ||
| Controller unit (W×L×H) | 108× 191 × 59 mm3 | ||
| Power adapter (W×L×H)12) | 50 × 125 × 31 mm3 | ||
| Harmonic generator (W×L×H)13) | 110 × 242× 112 mm3 | ||
| Operating requirements | |||
Cooling requirements | Air cooled | ||
| Ambient temperature | 15 – 30 ºC | ||
| Relative humidity | 10 – 80 % (non-condensing) | ||
| Mains voltage | 90-230 VAC, single phase, 47-63 Hz 14) | ||
| Average power consumption | <40 W | ||
- Due to continuous improvements all specifications are subject to change. Unless stated otherwise all specifications are measured at fundamental wavelength and maximum pulse repetition rate. The parameters marked typical are not specifications. They are indications of typical performance and will vary with each unit we manufacture.
- Factory-set pulse repetition rate is fixed at max repetition rate shown in the table. Smoothly variable pulse repetition rate is possible when laser is externally triggered. In internal triggering mode repetition rate can be divided by integer number down to f/2, f/3, f/4,.. 1 Hz.
- At FWHM level at fundamental wavelength, measured with 350 ps rise time photodiode.
- Pulse energies for harmonic wavelengths are maximum possible values available from H1 series harmonic generator module. See datasheets of H1 for details.
- Measured during 30 seconds operation after warm-up.
- Over 8 hour period after 20 minutes of warm-up when ambient temperature variation is less than ±2 °C.
- Full angle measured at the 4σ level.
- Peak to peak value, measured for 30 seconds of operation after laser warm-up.
- Beam diameter is measured 20 cm from laser output at the 4σ level.
- In respect to falling edge of pump diode triggering pulse.
- Motorized attenuator intended to be attached to the laser housing. Transmission can be changed remotely trough laser web-server control interface.
- Power adapter dimensions might differ from indicated here, depending on model.
- Q1 laser is compatible all models of stand-alone H1 harmonics generator. Please refer to harmonic generator datasheets for detailed specifications.
- Laser can be powered from appropriate 12 VDC power source. Please inquire for details.
